| 8000 |
Insufficient data on file MODLCF. |
| 8001 |
Time value on file MODLCF < -99990. |
| 8002 |
HTF AND SINK Cards are improperly ordered on file MODLCF. |
| 8003 |
Error in TMG input file INPF: Element label <ID> on Card 9 too large. |
| 8004 |
Error in TMG input file INPF: Only group names are allowed on INTERP
Cards with the TDTHCON option. |
| 8005 |
Error in TMG input file INPF: Element <ID> on Card 9 INTERP Card does not exist. |
| 8006 |
Error in TMG input file INPF: Table no <number> does not
exist. |
| 8007 |
No conductance found between elements <ID> and <ID>. |
| 8008 |
Start time is less than the lowest Start Position time defined in any Orbital Heating entity and the lowest time value defined in any time-varying Heat Load or Heat Flux entity. Start time < minimum time defined in radiation request or time dependent heat load. |
| 8009 |
Start time > maximum time defined in radiation request or time dependent heat load. |
| 8010 |
Table number <number> is a duplicate. |
| 8011 |
Missing interpolation table variable type definition for table number
<number>. |
| 8012 |
Missing interpolation table data for table number
<number>. |
| 8100 |
Solid element <ID> has coincident nodes. |
| 8101 |
Solid element <ID> has collinear nodes. |
| 8102 |
Solid element <ID> has <integer> nodes associated to it. TMG
supports only solid elements with 4, 6, or 8 nodes. |
| 8103 |
Error in TMG input file INPF: Orthotropic material defined with nodes
<IDs> has improper nodes. |
| 8104 |
Error in TMG input file INPF: Orthotropic material defined with nodes
<IDs> has improper directions. |
| 8105 |
Error in solid element <ID>. Either orthotropic properties are improperly defined, or, more probably, material angles are either not defined or are improperly defined. |
| 8110 |
Interpolation table number <number> not found for joint
<ID>. |
| 8111 |
Invalid interpolation table type for joint <ID>. |
| 8112 |
Reverse side of transparent element <ID> is not defined. |
| 8113 |
Reverse sides are not defined for <number> transparent elements:
<list of IDs> ... |
| 8114 |
Multiple spin requests have been specified with different spin axes. All spin requests in one model must have the same spin axis. |
| 8115 |
The model only consists of elements which are not yet supported by the finite element method such as 0D lump mass, 1D beams, 2D shells with zero thickness. In such a configuration, a parallel run cannot be operated. Please revisit the solution configuration in order to perform the thermal solve in serial. |
| 8200 |
TMG Security Error 2011 TMG License Has Expired or Security Violation. TMG Error 2011 - TMG license has expired or security violation. |
| 8201 |
TMG User Count Exceeded for <name> Module. TMG user count exceeded
for <name> module. |
| 8202 |
TMG Security Error 2016- <number>. TMG security error 2016-
<number>. |
| 8203 |
TMG Security Error 2015 - Usercount Error <number>. TMG security
error 2015 - usercount error <number>. |
| 8204 |
Referenced node <ID> does not exist. |
| 8205 |
Error writing on file MSGF. |
| 8206 |
TMG Security Error 2031 Your TMG Installation has Expired. TMG security error 2031 your TMG installation has expired. |
| 8207 |
TMG security error 2006 - contact TMG support. TMG security error 2006 - contact TMG support. |
| 8208 |
TMG Security Error 2018 Corrupt Client Database. TMG security error 2018 corrupt client database. |
| 8209 |
TMG security error 2013- <number> could not read TMG security
files. TMG security error 2013- <number> could not read TMG security
files. |
| 8210 |
TMG security error 2013- <number> could not decode TMG security
files. TMG security error 2013- <number> could not decode TMG
security files. |
| 8211 |
TMG security error 2017 invalid client database. TMG security error 2017 invalid client database. |
| 8212 |
TMG security error 2020 unregistered client. TMG security error 2020 - unregistered client. |
| 8213 |
Absolute value of free convection exponent <value> is >
5.0. |
| 8214 |
TMG Security Error 2019 No Current License. TMG security error 2019 no current license. |
| 8215 |
TMG Security Error 2020 Contact TMG Support. TMG security error 2020 contact TMG support. |
| 8216 |
TMG Security Error 2012 Contact TMG Support. TMG security error 2012 contact TMG support. |
| 8217 |
Error in <name> module. |
| 8218 |
Error in readcont subroutine. |
| 8219 |
Incorrect data type <integer> in GETPUT. |
| 8220 |
Incorrect element no <integer> in GETPUT. |
| 8221 |
GETPUT entered recursively, ielem= <integer> itype=
<integer>. |
| 8222 |
Unable to allocate array <integer> from FGETMEM2. |
| 8223 |
Error in PUT routine, IARR= <integer> IEL= <integer> IEL2=
<integer>. |
| 8224 |
File <name> is being opened with the improper unit number
<number> should be <number>. |
| 8225 |
Articulation parameters, or an orbit, diurnal heating, or solar heating request must be defined with an articulation request. |
| 8226 |
Meshing of the earth failed, possibly due to a low H/R value. Try
using GPARAM 4 116 1 which activates an alternate earth meshing
technique. |
| 8227 |
Interpolation fails for element ID <ID> from table
<number>. |
| 8228 |
Failed to parse the following string for expression ID <ID>:
<name> for BC or element selection group name: <name>. |
| 8229 |
Unrecognized field or variable name <name> encountered for
expression ID <ID>: <name> for BC or element selection group name:
<name>. |
| 8230 |
Expression evaluation failure for expression ID <ID>: <name>
for BC or element selection group name: <name> occurring at time =
<value>. |
| 8231 |
Array number <number> is outside of the permitted range
[2001-2500] |
| 8232 |
Non-existent entity IDs referenced as function arguments in expressions |
| 8233 |
No available array number is found in the range between <integer>
and <integer> |
| 8234 |
Failed to copy file <name> to <name> with error code
<number> |
| 8235 |
The table <number> has an option LOG_LINEAR. However, the
independent variable (argument) <value> is negative that is not a
valid value for the log function. |
| 8236 |
The table <number> has an option LINEAR_LOG. However, the
dependent variable (function) <value> is negative that is not a valid
value for the log function. |
| 8237 |
The table <number> has an option LOG_LOG. However, the independent
variable (argument) <value> is negative that is not a valid value for
the log function. |
| 8238 |
The table <number> has an option LOG_LOG. However, the dependent
variable (function) <value> is negative that is not a valid value for
the log function. |
| 8239 |
The number of spatial dimensions for the table <number> is one.
For Delaunay interpolation method, at least two spatial dimensions must
be provided. |
| 8240 |
There are no values specified for the table <number>. Please
specify at least one value. |
| 8241 |
The specified number <value> for the fraction of all points for
the table <number> is too low. Please specify a larger
number. |
| 8242 |
The number of spatial variables <integer> is incorrect for the
table <number>. Please check and correct this table. |
| 8243 |
There are more than one non-spatial variables specified for the table
<number>. Please specify no more than one non-spatial
variable. |
| 8244 |
There are fatal errors in the autoconnected stream topology. Please see the above messages for more information. |
| 8245 |
There are fatal errors in the parallel run domain decomposition. Please see the above messages for more information. |
| 8801 |
M=256 obsolete restart option - please use M=0 option
instead. |
| 8802 |
Error in TMG input file INPF: Missing title Card. |
| 8803 |
File CHKPNT is present, analysis cannot proceed. Please delete or rename this file. |
| 8804 |
File INPF not present in run directory, analysis cannot proceed. |
| 8805 |
No machines are available to run <name> in parallel. Run command
mpdboot; or mpd on the primary machine and mpd -h hostname -p
port_number on the remote machines to set up the machine chain. |
| 8806 |
A machine file is given but no machines in the file are available to
run <name> in parallel. Double check the machines in the file and
make sure that smpd/mpd processes are running and chained to the primary
machine if on unix/linux. The machine file name is <name>. |
| 8807 |
A machine file is given but the file is not accessible. Thus no
machines are available to run <name> in parallel. The specified
machine file name is: <name>. |
| 8808 |
TMG tries to filter the machines from the given machine file and
writes to a temporary machine file in the run directory to run <name>
in parallel. However, the output file cannot be opened to write the
machines in the run directory. The temporary output file name is:
<name>. The given input machine file name is: <name>. |
| 8809 |
When attempting to run <name> in parallel, MPI was unable to
connect to the primary machine without prompting for user login
credentials. Please use mpiexec -register or equivalent command on the
primary machine and on all other machines in your machine file. Then
reattempt the run. The primary machine is the machine where this TMG run
was launched and TMG files are stored. The primary machine name in this
TMG run is: <name>. The specified machine file name is:
<name>. |
| 8810 |
No machine file can be found! To run <name> in parallel on this
platform, a machine file must be specified in which participating
machines are listed. If this file is not given in INPF, TMG tries to
open a default machine file in the following order: 1) mayampi.hosts in
the local run directory; 2) $SDRC_TMG/if/tmgmpi.hosts. Neither of above
exists. |
| 8811 |
A Fortran user-written subroutine was found, and the PARAM USERDLL option was also specified. This combination requires double precision. Please ensure that the specification: DOUBLE PRECISION T(*),TIME,DT is present in your user-written subroutine. |
| 8813 |
PARAM ANADOMDEC/DOMDEC/RADDOMDEC option is on but neither mayampi.hosts nor tmgdomdec.setup file is provided in the run/solution directory. Please run the parallel machine validation tool to have file mayampi.hosts written automatically. |
| 8814 |
Error retrieving data from table <number>. Either the table has no
entries or has invalid dependent or independent variables. |
| 8815 |
View Factors GPU option in Parallel Configuration File must be activated. |
| 8990 |
More than <integer> conductances in module CONN2. |
