| 15501 |
Could not associate cyclic zone <name> to <name>. |
| 15502 |
Cyclic zone <name> has no eligible elements. |
| 15503 |
Detected a target node that belongs to a shell element as well as to a non-shell element. |
| 15504 |
Could not associate thermal zone <name> to <name>. |
| 15505 |
Could not associate flow zone <name> to <name>. |
| 15506 |
Thermal zone <name> has no eligible elements. |
| 15507 |
Flow zone <name> has no eligible elements. |
| 15508 |
Symmetry zone <name> used for mapping overrides the axis defined as FEM axisymmetric extension. |
| 15509 |
Symmetry zone <name> used for mapping contains axisymmetric meshes that have been overriden. |
| 15510 |
Could not associate symmetry zone <name> to <name>. |
| 15511 |
Symmetry zone <name> has no eligible elements. |
| 15512 |
Unable to determine the thickness for the gradient pair (<ID>,<ID>). |
| 15513 |
Could not associate transverse grad zone <name> to <name>. |
| 15514 |
Transverse grad zone <name> has no eligible elements. |
| 15515 |
Output is requested for structural solver(s) that expect temperature gradient results on nodes. The transverse grad target zone <name> only contains elements. No nodal values will be mapped for this zone. |
| 15516 |
Output is requested for structural solver(s) that expect temperature gradient results on elements. The transverse grad target zone <name> only contains nodes. No elemental values will be mapped for this zone. |
| 15517 |
Unsupported element type <type>. |
| 15518 |
Unsupported node card. |
| 15519 |
Unsupported element card. |
| 15520 |
Hydraulic element found. |
| 15521 |
Field data are not available at time <value>. |
| 15522 |
Unsupported unit system. |
| 15523 |
Source model contains non-axisymmetric meshes. Regular mapping will be applied. |
| 15524 |
Source model contains inconsistent axisymmetric meshes with variable axis coordinates and/or segment numbers. Regular mapping will be applied. |
| 15525 |
Source model contains axisymmetric meshes with unsupported axis values. The only supported axis are OX, OY, OZ. Regular mapping will be applied. |
| 15526 |
Source model contains elements that do not all belong to a single plane containing the axis. Regular mapping will be applied. |
| 15527 |
Source model does not have an axisymmetric extension. Regular mapping will be applied. |
| 15528 |
No results of the requested type are found. |
| 15529 |
Source alignment points MAP <ID> and MAP <ID> are too close to each other. |
| 15530 |
Target alignment points MAP <ID> and MAP <ID> are too close to each other. |
| 15531 |
Source and target alignment point sets are not similar. |
| 15532 |
The bun file to append to already contains results for the some of the nodes. Those results will be ovewritten by the new mapping results. Here are some of those nodes: |
| 15533 |
Transverse gradient values are currently not supported with TMG input files and have been omitted from the <*.gtempf> and <*.tempf> files. |
| 15534 |
Transient output times are not specified. Mapping will be done at all printout times. |
| 15535 |
Source data are not available at time <value>. |
| 15536 |
The requested output time <value> is outside the range of the source file. The closest source time data were used for mapping. |
| 15537 |
Field data are not available at the exact time <value>.Instead using the data at time <value>. |
| 15538 |
Unsupported parameter <name>. |
| 15539 |
Unsupported parameter <name> and value <name>. |
| 15540 |
The source environment <name> is different from the target environment <name>. This may lead to wrong mapping results and should be avoided. |
| 15541 |
The target model contains mixed order elements. The current value of the MIXED_ORDER_OPTION in fldmap.prm file in the run directory is either OFF or NO_RESULTS and therefore no mapped temperature bun file has been created. To create the bun file with results on all nodes, set the MIXED_ORDER_OPTION to MIXED_ORDER. To create the bun file with the mixed order elements displayed as linear elements, set the MIXED_ORDER_OPTION to LINEAR. |
| 15542 |
The target model contains mixed order elements. The current value of the MIXED_ORDER_OPTION in fldmap.prm file in the run directory is either LINEAR or ON and therefore the mixed order elements are represented as linear elements in the mapped temperature bun file. To create the bun file with results on all nodes, set the MIXED_ORDER_OPTION to MIXED_ORDER. |
| 15543 |
Invalid target model. It does not seem to have a mesh. |
| 15544 |
No results of <type> type are found in source file. |
| 15545 |
The alignment translation based on MAP1 points would break source model axisymmetry. To avoid this, no translation is done for the radial component. |
| 15548 |
The <Append Results> function is enabled, but the requested output times are different from those in the file to append to. The results in the file to append to will be interpolated to the requested output times. |
| 15549 |
The bun file to append to already contains results for the following nodes. Those results will be ovewritten by the new mapping results. |
| 15550 |
The alignment translation based on Source Model Mapping simulation object would break source model axisymmetry. To avoid this, no translation is done for the radial component. |
| 15551 |
For the Source Model Mapping simulation object, "Axis and Angle" method is selected and a non-zero angle is defined. However, no Rotation Axis is defined. Rotation transformation will be ignored for this mapping solution. Please revise the SO dialog in the UI and define a rotation axis if Rotation transformation is desired. |
| 15552 |
The mapping geometry source file tmg50.h5 does not exist. However, the source model is of finite element type. Make sure that the source file tmg50.h5 is present in the mapping source directory: <name>. |
